Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
The article listed below pertaining to Installing A Bathtub is exceedingly compelling. Check it out yourself and decide what you think about it.
Setting up a bath tub isn't specifically rocket science, however it does call for solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably hard task. If the old bathtub is readily available, the project can move immediately; if you need to open up a wall to eliminate the old tub as well as place the brand-new bathtub, the task is much harder. In either situation, the job is within a home handyman's skills, although you will certainly need a helper to leave the old bathtub and also embeded in the brand-new one. See to it you have certified yourself for the job and are comfortable trying it. Instead of hiring a contractor to take over a halfway-completed task, it is far better to think about utilizing one before you start. Chances are you might require an expert plumber to make tube connections.
This article will aid you mount a brand-new tub in your restroom if you have actually currently gotten a new tub and do not require to alter the arrangement of your previous supply of water pipes.
Your tools and also product checklist should consist of the following:
Getting ready for the Installation
Firstly, the supporting structure provided with the bathroom ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is necessary to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets device to avoid pressure on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath should now prepare to be fitted in its final placement.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water. After doing so, turn on the faucets to drain pipes any water staying in the system. The procedure of removing the existing faucets can be fairly problematic because of the limited access that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the staying water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Prior to moving on to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, place the bathtub in the needed placement. The wood boards are useful in equally spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four small points.
The next objective is to guarantee that the tub is leveled all round. This can be attained by examining the spirit level and adjusting the feet on the tub up until the level reviews degree.
To mount taps, fit the bottom of the furthest flexible tap port to the proper supply pipe by making a compression sign up with; then do the same for the other tap.
Activate the water supply and also examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bathtub and additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Ultimately, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and also securing around the tub ought to wait until the bathtub has actually been utilized a minimum of once as this will certainly resolve it right into its final position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin making certain that the washing machines remain in place between the faucet as well as the sink. Protect the tap in position with the maker offered backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with normal faucet ports. The former kind must be linked to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bathroom satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to fracture a stiff seal, causing the water to pass through the wall between the bathroom as well as the tiling, leading to issues with dampness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components as well as installations. They are offered in tubes and also cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to allow for the activity experienced when the tub is in usage. The sealant can split fairly early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly available on the market. It is a good idea to fit the tiles utilizing waterproof or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you enjoyed our section on How to Install a Bathtub. Thanks a ton for taking a few minutes to read our posting. Liked our piece of writing? Please share it. Help someone else find it. We value reading our article about Installing A Bathtub.
Give Me A Quote! Report this page